Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may want to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be completed in just a few steps.

First ensuring your red dot sight is turned on.
Locate the small reinitialize button on the rear of the sight.
Employ a paperclip to activate the reset switch for approximately three moments.
Let go the switch and your Holosun EPS Carry Red Dot sight will reboot.
The red dot sight should now be returned to its factory settings.

Return to Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it back to standard configuration is a breeze. First, locate the tiny button on the rear of your optic. Then, sustain it for around ten seconds until you here see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for precise aiming.

restore Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

Simultaneously press and hold the power button for approximately 5 seconds.
An indicator will flash, indicating that the reset is in progress.
Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and confirm your sight's functionality. If you encounter any further problems, don't hesitate to seek help from Holosun's support.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

Beginning with, Energize your Holosun EPS Carry by pressing the power button.
Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
While continue holding these buttons, tap the power button once.
The display will show a confirmation prompt indicating that the reset process is initiated.
Permit the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reset your Holosun EPS Carry with a Factory Default Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the solution. This will restore your sight to its original settings, clearing any personalized configurations you've made. To accomplish this reset, observe these simple steps:

To begin, identify the reset switch on your EPS Carry.
Then, press a thin object, like a toothpick, to activate the reset lever.
While maintain the reset button activated, turn your EPS Carry.
The sight will flash a message showing that the reset is complete.

After the reset is finished, your EPS Carry will be set to its factory settings.